SURFACE PREPSurfaces must be clean, bare and porous. Remove paints, sealers, curing compounds, adhesives, oil, grease, mold, efflorescence and other contaminants that might interfere with the penetration of the sealer. Hard-troweled concrete surfaces require chemical etching or mechanical abrasion to increase porosity. A sufficiently porous surface should readily absorb the sealer.
The Armor AR500 is a solvent based high The Armor AR500 is a solvent based high gloss acrylic concrete sealer designed to seal and enhance concrete and paver surfaces. The durable, non-yellowing high gloss finish offers superior resistance to rain, the sun, cold and hot climates, stains and more. Aug 01, 2010 Find out what type of concrete sealer to use for different applications. For example, different sealers are used for interior and exterior concrete. Tips on concrete sealer selection.
Use to obtain a proper surface profile. If chemical cleaners or concrete etchers are used, be sure to throughly rinse and remove them prior to sealer application. Mask surfaces not intended to be sealed. Vacuum or blow off excessive dust and loose particles. Make necessary repairs to cracks, joints, and defects before sealing. APPLICATIONHand-pump sprayer equipped with fan tip nozzle (preferred), airless sprayer regulated below 40-psi, roller, or brush.STEP 1: Attach mixing tool to your power drill.STEP 2: Remove cap on the top of the pail and insert the mixing tool. Thoroughly mix while adding the entire contents of the activator bottle (about 3 minutes).STEP 3: Fill pump-sprayer with mixed sealer.STEP 4: Spray Ion-Bond Armor uniformly to the surface, maintaining a continuous wetting film.
On vertical surfaces, apply from the bottom up maintaining a wet edge.STEP 5: Spray Ion-Bond Armor uniformly to the surface, maintaining a continuous wetting film. On vertical surfaces, apply from the bottom up maintaining a wet edge.
How long does it take concrete esaler to dry? The amount of time it takes for concrete sealers to dry will depend on the type of concrete sealer used.: Silicate sealers are used to reduce dusting and increase the surface strength of the concrete. They won't change the look or color of the concrete and work entirely below the surface. Silicate concrete sealers will appear to have dried in as little as 30 minutes, but they will continue to react below the surface for up to 90 days.
Typically you can walk on concrete sealed with a silicate sealer in as little as a few hours.: Silane-Siloxane sealers are used to reduce damage, deterioration, and staining caused by water absorption, freeze-thaw cycles, and de-icing salts. They are also used to reduce the formation of mold, mildew, and efflorescence. They won't change the look or color of the concrete and work entirely below the surface. Silane-Siloxane concrete sealers will appear to have dried in as little as 30 minutes, but they will continue to react below the surface for up to 72 hours. While you can walk on the concrete sealed with a Silane-Siloxane sealer shortly after being sealed, the concrete should remain dry for 36 hours after being sealed to allow the sealer to fully react.: Siliconate sealers are used to reduce damage, deterioration, and staining caused by water absorption, freeze-thaw cycles, and de-icing salts. They are also used to reduce the formation of mold, mildew, and efflorescence.
They won't change the look or color of the concrete and work entirely below the surface. Siliconate concrete sealers will appear to have dried in as little as 30 minutes, but they will continue to react below the surface for up to 24 hours. While you can walk on the concrete sealed with a Siliconate sealer shortly after being sealed, the concrete should remain dry for 36 hours after being sealed to allow the sealer to fully react.: Acrylic sealers are used to enhance and protect interior and exterior concrete with a wet look, low gloss, or high gloss finish. Acrylic sealers can take anywhere from 4-12 hours to dry before being able to be walked on, but they will continue to harden for up to 48 hours after being applied. Concrete sealed with an acrylic sealer should not be walked on (with the exception of a recoat), driven on, or wet for at least 36-48 hours.: Epoxy coatings are designed to enhance and protect interior concrete floors. The dry time of an epoxy will depend on the type of epoxy used.
It is best to speak with the manufacturer. Typically, it can take anywhere from 10-12 hours to dry before being able to be walked on, but they will continue to harden for up to 48 hours after being applied.
Concrete sealed with an epoxy coating should not be walked on (with the exception of a recoat), driven on, or wet for at least 36-48 hours.: Urethane coatings are designed to enhance and protect interior concrete floors from exposure to oil, gas, and chemicals. The dry time of a urethane will depend on the type of urethane used. It is best to speak with the manufacturer.
Typically, it can take anywhere from 10-12 hours to dry before being able to be walked on, but they will continue to harden for up to 48 hours after being applied. Concrete sealed with a urethane coating should not be walked on (with the exception of a recoat), driven on, or wet for at least 36-48 hours.Need a concrete sealer, but aren't sure which concrete sealer is best? View our page to find out which concrete sealer is best for your concrete.